Skip to main content

Posts

Showing posts from December, 2012

How to solve message Waiting for tray 0 to lift with HP Laserjet printers

The message error Waiting for tray 0 to lift appears on these printers: HP CM6030, CP3525, CP4005, Laserjet 4000, 4200, 4250, 4350, 4700, 5500, 9040... Paper is in the tray but no motors turn. Solution 1: Turn the printer off.  Remove the Network Card.  Do a cold reset. Install the network card. Solution 2: Download and install the latest firmware. Solution 3: Take the paper out of the trays and check the trays mechanism, lift the tray by hand and make sure nothing is obstructing the movement or something broken. Solution 4 : Remove the toner. Lift the registration plate up. Check for torn pieces of paper blocking one of the sensors.

Error 13.09.00 on HP Color LaserJet 4600

Error 13.09.00 indicates a paper delay jam has occurred. Remove any stuck media from the fuser access area, the duplexer area (if equiped) or the face down (top output) bin. The fuser may have a sticky exit sensor and is sensing the paper is there too long and throws up a jam.

Error 60.02 on HP Laserjet 4250 series

It appears that the spring which holds the lifter motor upright was designed without enough tension on it. If the spring is removed and the motor assembly is allowed to fall to the right when the paper tray is inserted the motor never engages the tray and an error 60.02 appears. However if the motor assembly is held upright while the tray is inserted the error message never appears as the motor always engages.

HP Laserjet 49 errors

HP laserjet 49 errors are a firmware error, it might be caused by the firmware itself, or by the failure of a printer module. How to isolate the cause: Verify that the problem is not being caused by a specific job, this error can be caused by bad information being sent to the printer. Power off and remove any installed EIO devices, (JetDirect Cards, Hard Drives), power on and test. Cold Reset the printer: Power off, remove any optional memory, power on and retest. Power off and reseat any memory and firmware modules on the formatter board, power on and test. Power off, reseat the formatter board, power on and test. Check firmware version : On newer machines with flashable firmware upgrade to the latest version. If you are running the latest version reload it, this might fix corrupted firmware. (Some printers have flashable firmware, others use a Firmware DIMM which must be replaced to upgrade.) If you haven't found the cause yet, it could be: The firmw

Samsung CLP-510 service manual

The Xerox 6100 is equivalent to the Samsung CLP-510 service manual : https://www.office.xerox.com/partners/products/Phaser6100/Phaser6100Se ries.html   Xerox phaser 6100          Samsung CLP-510 Link : Solutions for resetting Image Unit, Fuser, Transfer Roll, MP Pick-up, Tray 1 Pick-up

Reset purge counter for Brother MFC-J265W

To reset the purge counter of Brother MFC-J265W: Unplug the power cable. Hold down the " Start " button. Without release the "Start" button, connect the power cable. When "Maintenance" appears on the screen, release the "Start" button. Enter 80 with the numerical keypad. With down button go to the purge counter: "Purge00xxx" Enter 2783 with the numerical keypad. Press on "Stop/Exit" to go back in Maintenance mode Enter 9 and 9 to quit the Maintenance mode. This solution is available for these Brothers printers too: MFC-210C, MFC-215C, MFC-235C, MFC-260C, MFC-240C, MFC-250C, MFC-255CW, MFC-295CN, MFC-297C MFC-3240C, MFC-3340CN, MFC-3342C, MFC-3360C MFC-410CN, MFC-420CN, MFC-425CN, MFC-440CN, MFC-465CN, MFC-490CW MFC-5440CN, MFC-5840CN, MFC-5460CN, MFC-5860CN, MFC-5490CN, MFC-5890CN, MFC-5895CW, MFC-620CN, MFC-640CN, MFC-640CW, MFC-660CN, MFC-665CW, MFC-680CN, MFC-6490CW, MFC-6890CDW MFC-790CW MFC-8

Error 3501 on Kodak Easyshare 5100 and 5300

Error 3501 is a problem of calibration. Solution 1: Place the calibration sheet on the scanner. Then press the "Start" button. Solution 2 : Enter in the " Kodak All-in-One Home Center " Select "Help (?)" icon. Select " Maintenance " Select " Firmware Upgrade " Follow the prompts and download the latest version of firmware.